Truck Inventory Sheet Template for Service Techs
A truck inventory sheet template for HVAC, plumbing, and electrical techs: per-truck par levels, weekly checklists, A2L stocking notes, and restocking ROI math.
Per-truck par level logic
Set par levels by trade and call mix, not by what fits the bins. HVAC residential service truck: run capacitors 2 each across the common MFD ladder (5/7.5/10/15/20/25/30/35/45, plus dual-run 35/5 and 40/5 for condensers), contactors 2 each (1P/2P/3P at 24V coil, 30/40A), hard-start kits, refrigerant lines, common controls, basic copper. Mirror the established branded lists (Totaline cooling/heating stock lists, the Mr. HVAC/Aptora 700-plus item sheet with min/max levels) rather than inventing your own from scratch. Plumbing service truck: cartridges for top 4 brands, basic compression fittings, common gaskets, snake, basic flanges. Electrical: top 6 breaker amperage values, common receptacles, GFCIs, AFCI, common conductors. Flip par levels seasonally (capacitors, contactors, and refrigerant for summer cooling load; igniters and flame sensors for winter) and adjust by your service area equipment mix.
Weekly inventory check (Monday morning)
Tech runs through the truck inventory sheet first thing Monday. Marks shortfalls against par. Submits to dispatcher or warehouse. Shortages restocked by EOD Tuesday. Total time: 8 to 12 minutes per tech. Worth it: that 10 minutes protects against the parts run that costs an hour of billable time mid-week. Without a Monday check, par levels drift and FTF drops by Friday. The check works best when techs can also order from the field, so the truck is a stocking location, not a private hoard. ServiceTitan, FieldEdge, and similar tools track each truck as a location and prompt replenishment as parts get consumed on invoices, which is the digital version of this Monday sheet.
Restock cadence
Tier 1 (high-velocity, common parts): restock weekly. Tier 2 (specialty, infrequent): restock on demand or monthly. Tier 3 (rare, season-specific): pull from warehouse only on assignment. Mismatching tiers (treating tier 1 as on-demand) is what causes most FTF gaps. New for 2025-2026: the A2L refrigerant transition changes what HVAC trucks carry. Under the EPA AIM Act, new residential and light-commercial systems shipped after January 1, 2025 use low-GWP refrigerants, mainly R-454B (GWP 466) and R-32 (GWP 675), in place of R-410A (GWP 2,088). These are A2L (mildly flammable), so servicing them needs A2L-rated recovery machines and gauges, spark-resistant tools, and left-hand-thread adapters since A2L service ports are reverse-threaded to block cross-connection. R-410A is still legal to service existing systems, but supply is tightening and prices have spiked, so stock it as a managed Tier 2 item, not an afterthought.
ROI math
A 10-tech HVAC shop missing 3 to 5 stocked-part fixes per tech per week: 30 to 50 recalls per week. Each recall costs $150 to $300 in labor and drive plus lost capacity, which lines up with ACCA's 2025 figure of roughly $84 per hour to roll a truck once wages, benefits, vehicle, insurance, and non-billable windshield time are loaded in, before any profit. Annual cost: $234K to $780K. Truck inventory completeness investment to fix this: $1.5K to $3K per truck per quarter, plus inventory check time. ROI is typically 8 to 30x. The honest caveat: do not over-stock to chase the last percent. Parts that sit on a truck for months tie up cash and walk off as shrinkage, so the goal is the right Tier 1 par level, not a fuller bin.
When to upgrade to inventory software
At 5-plus trucks, manual sheets break down. Use FSM-native inventory (ServiceTitan, FieldEdge, BuildOps) or a dedicated tool (Sortly, ServiceFusion Inventory). ServiceTitan has the deepest inventory in the category, with per-truck stock templates, automated replenishment as parts hit invoices, serial tracking, and a barcode-scanning mobile app, but it is quote-based and typically runs in the $245 to $398 per technician per month range aimed at established shops. FieldEdge is the lighter, QuickBooks-anchored option at roughly $100 to $125 per user per month, with inventory as an add-on near $39 per month. The barcode scan plus auto-replenish loop is the real upgrade over a spreadsheet, since it kills the manual count drift. Below 5 trucks, the spreadsheet template works fine and the software cost is hard to justify.
Frequently asked questions
How do I set par levels for a new truck?
Start with 30 days of dispatched job data (or an industry baseline by trade, or a branded list like the Mr. HVAC/Aptora 700-plus item sheet). Stock for 80 percent of dispatched jobs, since chasing the last 20 percent means carrying rare parts that mostly sit and tie up cash. Refine based on actual recall data after 60 to 90 days: the parts that show up in your repeat-trip log are the par levels you raised too low.
What about specialty parts?
Tier 2 and tier 3 specialty parts stay in the warehouse. Tech pulls them when assigned a matching job. Stocking specialty on the truck wastes space and increases lost-part rate. The one specialty category to plan for now is A2L: as more R-454B and R-32 systems land in your service area, the matched gauges, recovery gear, and left-hand-thread adapters move from rare to routine, so review that par level every quarter instead of yearly.
How does Pineido help?
Truck inventory rollout is part of a 30-day dispatch or FTF improvement sprint. Includes par-level analysis from FSM job data, sheet buildout, and tech ride-along.
Get operations insights weekly
Join service-business operators who get one actionable insight on ops, automation, and growth every week.
No spam. Unsubscribe anytime.
You’re subscribed! Look for our next issue in your inbox.
That did not go through. Please try again, or email [email protected].
Ready to ship?
Tell us where you are stuck. We will review it and send a focused recommendation within one business day.